How To Clear A Clogged Washer Drain Pipe

How To Clear A Clogged Washer Drain Pipe

If your washer is not draining properly, you may need to clear a clogged washer drain pipe. Here are four steps to follow: 1. Turn off the water to the washer.
2. Open the front and side water valves. 3. Clear the obstruction from the drainpipe with a plunger. 4. Close the water valves and turn on the water to the washer.

Washing Machine Water Drain Clogged

How to clear a clogged washer drain pipe

There are a few different ways to clear a clogged washer drain pipe. You can try using a plunger, using a snake, using a vacuum cleaner, or using a bucket.

If using a plunger, first make sure that the plunger has a tight fit around the drain pipe. Then, push the plunger up and down the drain pipe several times. If the clog is small, the plunger may be able to remove the obstruction. If the clog is bigger, the plunger might not be able to remove it and you will need to use one of the other methods listed.

If using a snake, first make sure that the snake is long enough to reach the obstruction. Then, insert the snake into the drain pipe and pull it up and down several times. If the obstruction is small, the snake may be able to remove it. If the obstruction is bigger, the snake might not be able to remove it and you will need to use one of the other methods listed.

See also  How To Clean A/C Drain Pipe

If using a vacuum cleaner, first turn the vacuum cleaner on its side so the hose is facing the obstruction. Then, put the vacuum cleaner into the clogged drain pipe and turn the vacuum cleaner on. The suction will pull the obstruction out of the pipe.

If using a bucket, first pour a small amount of water into the bucket. Then, put the bucket over the obstruction and push and pull the bucket until

What you will need

– A plunger
– A bucket
– A snake
– A bucket
– A plunger
– A wire brush
– A bucket
– A plunger
– A plunger
– A bucket
– A bucket
– A bucket
– A bucket
– A bucket
– A plunger
– A plunger
– A plunger
– A wire brush
– A bucket
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A wire brush
– A bucket
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger
– A plunger

Step

The first step to clearing a clogged washer drain pipe is to determine the source of the blockage. This can be done by using a snake or a plunger to clear any obstructions from the drain pipe. If the obstruction is from dirt, sediment or mud, a plunger may be the best solution. If the obstruction is from plastic, metal or other materials, a snake may be necessary.

See also  How To Clear A Washing Machine Drain Pipe

Once the obstruction has been cleared, pour a pot of hot water onto the area around the drain pipe. This will help loosen any debris that has become lodged in the pipe. Use a plunger to suction onto the debris and pull it up and out of the drain pipe. Repeat the hot water and plunger procedure until the blockage has been cleared.

Step

  1. Turn off the water supply to the machine.
  2. Remove the water supply line from the machine.
  3. Unscrew the cover of the machine.
  4. Remove the screen from the machine.
  5. If there is a drain hose attached to the machine, detach the drain hose.
  6. Clear any obstructions from the drain pipe by using a plunger, snake, or a bucket.
  7. Clear the drain pipe of all debris by pouring a pot of hot water down the pipe and then turning on the water supply to the machine.
  8. Replace the screen, screw the cover back on, and reattach the drain hose.
  9. Turn on the water supply to the machine and wait until the water starts draining from the machine.
    10. Close the cover of the machine and turn off the water supply to the machine.

Step 3

  1. Clear the drain pipe by using a plunger. Push and pull the plunger up and down the pipe until the clog is removed.

    2. If the drain pipe is too large, you can use a garbage disposal to clear the clog. Insert the garbage disposal into the drain pipe and turn it on. The moving blades will loosen the clog.

    3. If the drain pipe is too small, use a snake to clear the clog. Insert the snake into the drain pipe and work it up and down the pipe. The snake’s smooth plastic surface will slide over the bumps and ridges in the drain pipe, removing the clog.

Conclusion

If your washer is not draining and filling up with water, it may be clogged due to build-up of laundry detergent and other debris. Here are some tips on how to clear a clogged washer drain pipe:

1. Remove any large pieces of debris that may be blocking the drain.
2. Pour a pot of boiling water onto the washer and let it soak for a few minutes. This will loosen any debris that is clogging the pipe.
3. Use a plunger to suction onto the pipe and push the debris down. Be careful not to damage the pipe.
4. If the drain is still clogged, you may need to call a professional.

See also  How To Clean Out A Drain Pipe Without A Snake

Leave a Comment

Your email address will not be published. Required fields are marked *